Elkhart-brass Scorpion 8394-04 Bedienungsanleitung

EELLKKHHAARRTT BBRRAASSSS MMFFGG.. CCOO..,, IINNCC.. 1302 WEST BEARDSLEY AVENUE • P.O. BOX 1127 • ELKHART IN 46515 • (574) 295-8330 • FAX (574)

7IV. CONTROL SYSTEM SPECIFICATIONS Controller Specifications • Power requirements 12VDC (9VDC to 14VDC) • Control current • Monitor motor run cu

8V. INSTALLATION A. Component Mounting See system layout drawing number 8294040 (part number 98284040) for pictorial of system layout. 1. Monitor

9Locate relay box enclosure close enough to monitor so that the properly secured cable will reach the monitor harness connection. The cable length

10 Figure 11 Panel Cutout and Mounting Hole Pattern for 81412001 and 81339001 Panel Mount Switch Module 4. 81340001 Secondary Switch Box ¾ Mar

11 5. 81466001 Auxiliary Battery ¾ Mark locations of mounting holes on mounting surface or bracket per Figure 13 ¾ Drill four (4) 21/64" dia

12 B. Electrical Connections 1. System Wiring Diagrams Refer to the appropriate wiring diagram (Found in instruction packet 98421001 included with

13¾ Strip off outer jacket of cable to a length of 4 inches. Pull cable back through strain relief so that just 1/4" of the cable jacket prot

14¾ Strip 5/16" of insulation from the ends of the black and white wires. Crimp insulated female disconnect type connector (16-14AWG) secure

15 Figure 16 Rotational Limit Settings for 8394-04 Application Rotation Limits Stop Screw Locations 45°Left or Right of Straight Ahead

162. Elevating Platform Water Delivery System (NFPA ¶16-13.2) The monitor(s) shall allow the operator to control the aimed direction of the nozzle

i Table of Contents I. Product Safety...1 II. System Features ...

17 VI. OPERATING INSTRUCTIONS A. Normal Operation The monitor and nozzle are controlled with three toggle switches at each control point. These sw

18VII. MAINTENANCE & INSPECTION For repair parts information see assembly-drawing number 08294041 (part number 98080000.) A. Preventive Monitor

19 LED Label Color Signal Significance +12V Power Yellow When lit, 12VDC power is available for operation of unit. If this LED dims upon

20VIII. MONITOR & NOZZLE HYDRAULIC DATA The following graphs offer the pressure losses for the monitor (and other devices) in terms of Total St

21 Figure 18 8294-04 and 8394-04 Scorpion Friction Losses Figure 19 284-A and 284-B Stream Shaper Friction Loss

DOCUMENT NUMBER 98167000 REVISION - B ELKHART BRASS MFG. CO., INC. P.O. Box 1127 · 1302 West Beardsley Ave. Elkhart, Indiana 46515

iiB. Manual Override ...17 C. Storing the 8294 Monitor (If available)

1I. PRODUCT SAFETY Important: Before installing and operating this equipment, read & study this manual thoroughly. Proper installation is

2II. SYSTEM FEATURES OPTIONAL ELECTRIC NOZZLES PRESSURE GAUGE USER SELCTABLE STOPS TO ADJUST VERTICAL TRAVEL LIMITS HIGH TORQUE MOTORS FOR RELAIB

3III. SYSTEM COMPONENT DESCRIPTIONS A. 8294-04 Scorpion Monitor (Figure 2) The 8294-04 Scorpion is a cast aluminum monitor with 4" waterway.

4mechanism for remote control of the spray pattern from a straight stream to wide fog. Another nozzle that my be used on this monitor is the ¾ S

5obstruction before reaching a limit, this circuitry quickly senses motor stall current and automatically shuts off power to the motor. As soon as

6 G. 81242001 Receptacle for Hand-Held Remote Control (Figure 6) This device consists of a Deutsch HD10 Series nine-conductor receptacle mounted in